Supply & Delivery of One (1) High-Pressure Water Jetting Truck

Summary and scope

Council is inviting Tenders for the supply and delivery to Queanbeyan-Palerang Regional Council for: One (1) only High-Pressure water Jetting Truck This is a SPECIALISED BODY SUPPLIER SOURCED contract. The body supplier will be responsible for the complete offer including the CAB CHASSIS. GENERAL a Registration The Unit is to be registered in accordance with Transport for NSW (TfNSW) requirements for Twenty-four (24) hour usage and road travel requirements. The unit shall comply with all necessary state and Federal statutory requirements. Reimbursement of the cost of registration will be made separately to the payment of the vehicle, therefore the cost of registration should be invoiced separately. Council does not have a common expiry date. b Delivery The successful tenderer is required to deliver the unit in a ready to use configuration including full registration. Delivery will be at Council’s Queanbeyan Depot located at 10 Ellerton Dr Queanbeyan NSW 2620. At the time of tender, tenderers are to state a firm date for the delivery of the machine. Advance notice of the delivery is to be at least five (5) working days. c Warranty and Servicing Tenderers are to state manufacturer’s warranty period and conditions including details of warranty servicing. Any items not covered under the name brand of the machine e.g. engines, transmissions, body etc, shall be included stating period and conditions. If this is not done it will be assumed that the warranty shown is covered for the whole of the machine under the names brand of the machine. Any additional warranty available and pricing advantageous to Council should be included. d Training The successful contractor will be required to provide training for the operators by a certified training officer and shall incorporate the following: • Routine daily maintenance checks including fluid levels, lubrication points, and start up procedures. • Use of the Plant item in various operating conditions. • Vehicle specific workplace safety aspects. • Occupational health and safety requirements for the operator. • Any requirements to operate machine in the correct manner. Training will be up to four (4) operators, documentation of the training and signing off by the operator must be carried out. e Manuals and Spare Parts The following items are to be supplied with the machine upon delivery: Two (2) operator manuals (one (1) permanently fixed in the machine cabin). f Build Date of Unit The truck is to be of current year build date. SPECIFICATION a Machine Minimum Requirements One (1) only 4 x 2 cab chassis fitted with Water Tank, Main Reel, Easement Reel Lifter, and Storage. The intended purpose of this vehicle is to provide a powerful cleaning solution to clear blockages in drains and sewers within the Queanbeyan-Palerang Regional Council Local Government area. The unit shall comply with the length, width and gross mass limits for general access vehicles as adopted under the national mass and loading arrangements and comply with all TfNSW requirements. The truck is to be fitted with the following minimum requirements (some of which may be standard equipment on the machine offered). ENGINE • ADR80/03 Diesel engine with a nominal minimum power output of 191kW at 2,400 RPM. • Two stage air filter with service indicator and high intake with pre-cleaner. TRANSMISSION • Automatic transmission. • PTO. CHASSIS • 4x2 Configuration. • GVM – 14 000 kg minimum. • Rear air bag suspension. • Rear diff lock. • Brake system to comply with ADR35. • Automatic adjusting brakes. • All external fluid tanks are to be lockable. • Heavy duty battery isolation switch with removable key or locking system. • Reversing alarm fitted • Steel wheel rims to be standard ISO 8 stud 6.75 x 19.5. • Front tyres to be 295/80R 22.5 tubeless radials highway/construction pattern. • Rear tyres to be 11R 22.5 tubeless radials. • Spare rim and tyre. • Recovery Tow Points on the front and rear of the truck chassis. • Safety items to be painted yellow • Standard one solid colour White • Reversing Camera within Cabin display CABIN • Cabin shall be forward control day cab. • Fully integrated air conditioning. • ‘Westcoast’ type heated rear vision mirrors, electrically operated from inside cabin, moving in both directions. • ‘Isri’ type driver’s seats with canvas seat covers, fully adjustable air ride including shock suspension and integral seat belt, lumber support. • Power windows. • Directional Arrow bar to rear • 12-24 voltage reducer if necessary (min 15amp) • 12-volt accessory outlet. • AM/FM radio with aux input and Bluetooth capability. • Heavy duty floor mats. • Sun visor • Aluminium bull bar. WATER TANK • Polyethylene 5000 litre baffled water tank. • Large inspection cover • Water level sight tube with indicator float. • Water infill point is anti-siphon compliant to AS/NZ 3500.1 for hydrant use (air gap). JETTING SYSTEM Pump • Pump to be capable of minimum 265 Litres/Minute at 2200 psi • Hydraulic pump mounted to PTO for hose reel functions • System engagement inside cabin Main Hose Reel 1” • Main hose reel is mounted at the rear of the unit for easy access. • Fabricated from heavy gauge steel • Mounted onto steel plate base with an industrial turntable bearing allowing for 180-degree rotation with locking points. • Hydraulically operated unwind and wind controls with free wheel position. • Variable speed on unwind and wind via high torque hydraulic motor direct drive with chain coupling and guard • Hydraulically operated layering arm with manual extension and hose roller box guide. • 183mt x 25mm (600’x1”) of low friction Piranha sewer hose rated at 2,500psi working pressure, 6,250psi burst pressure. 1 continuous length. • All hose connections to be NPT-NPT or BSPT-BSPT. • “Tiger tail” protector to suit Secondary Reel ½ “ • Mounted to the side of the main hose reel giving 180 degrees of rotation on same axis as main hose reel. • Fabricated from heavy gauge steel • Hydraulically operated unwind and wind controls with free wheel position. • Variable speed on unwind and wind via high torque hydraulic motor direct drive with chain coupling and guard. • 120mt x ½” low friction cover sewer hose. 4000psi working pressure 10 000psi burst pressure and Male hose fittings each end. • Handgun and lance operate from secondary hose reel. EASEMENT REEL LIFTING DEVICE • Truck to include an Easement Reel lifting device with easy load and unload. • Needs to be designed to lift an Easement Reel with 120 Metres of one (1)” sewer hose. Tender to include as optional extra, 1 Diesel Posi track Easement Reel with 120 Metres of one (1)” sewer hose and to include, • Layering arm • Must include safety anchor mechanism for main hose from truck Tender also to include as optional extras nozzle options/packages STORAGE AREAS • Truck must include multiple external storage areas. • All storage toolboxes must feature stainless steel hinges and be keyed alike • Minimum two (2) storage trays for shovels and crowbars. • Two (2) x large capacity toolboxes mounted under rear deck for small tools. • Sign rack & witches hat storage in front toolbox ELECTRICAL SYSTEMS AND CONTROLS • Handheld remote providing full function operation of the water pump and hose reel including emergency STOP button. • Safety protection – • Low water shut down • Emergency stops • drive mode lockout • low level hydraulic oil • Truck Idle function, the truck will immediately return to idle if either the water pump is turned off or the Emergency Stop button is activated • Low water shut down if the water runs below a certain point the unit will shut down to protect the water pump • Option – additional remote as described in dot point 1 above. b SIGN WRITING Sign writing is to be carried out on the machine prior to delivery consisting of the following: • Tare, GVM and GCM weights of vehicle. c ADDITIONAL SAFETY AND OTHER REQUIREMENTS • The truck is to be configured to carry the optional diesel posi track combination referenced above. • Two (2) LED night lights mounted at rear • One (1) LED night light located inside canopy • Two (2) revolving amber beacons mounted at the front and rear of the unit. • All safety label requirements • QPRC works with Plant Assessor for all safety requirements. Below are Plant Assessors requirements for safety which must be included in the tender. o Ensure all operator work platforms over 0.5 m have three points of contact or guardrails and above 2.0 m an approved guardrails prior to access. o Fit an automatic reverse movement sensor awareness alarm. o Fit e-stop device at each operator control area o Fit mechanical control to jetting lance (if required) o High pressure water hose marked to indicate nozzle location o Hose assemblies appropriately marked o Fit flow control device o Fit internal baffles to water tank o Fit pressure relief device to pump o Fit pressure gauge to discharge side of pump o If item of plant has hydraulic hoses; Fit hose protection o If item of plant is fitted with variable speed motor; Fit speed governor or overspeed trip device o If water blasting plant is a Class A (energy rating 800 - 5600 bar L/min): Pump fitted with compliance plate showing: Manufacturer name Model, serial number and year of manufacturer Max rated volume & pressure Hose to be clearly marked o If water blasting plant is a Class B (energy rating 5600 bar L/min): Pump fitted with compliance plate showing: Manufacturer name Model, serial number and year of manufacture Max rated volume & pressure Compliance with AS/NZS 3350.1 or AS/NZS 60335.1 Max input speed Max inlet water temperature Hoses, adaptors and end fittings to be appropriately marked If pressure is up to 3000 bar - ensure minimum burst rating of 2.5x max operating pressure If pressure is above 3000 bar - ensure minimum burst rating of 2x max operating pressure o If item of plant has a drawbar: Fit safety chain attachment points